Polycom 410 - 6 Account Limit
@mpelchat wrote: I'm trying to setup 13 lines on my Polycom VVX410 using Endpoint Manager (Latest Version). I get the first 6, but am unable to add any further. I thought I figured a way around it...
View ArticleClik here to view.
Endpoint Manager basfile edit: Activate additional lines
@SilkBC wrote: Hello, I am using FreePBX 12 with Aastra 6867i phones. These phones have two line enabled automatically, and i would like to enable an addition two lines globally. I am able to do this...
View ArticleCisco SPA525g2 Not Provisioning with EPM
@Allstates wrote: I am very New to Freepbx and really have limited knowledge of Asterisk. I am having trouble provisioning and updating the provisioning on several SPA525. I was able to provision one...
View ArticleFailover settings not applied to all accounts
@roll4life wrote: In attempting to configure a second, third, fourth line on a Sangoma s500 phone, I found that the redundancy settings that are set in end point manager are only applied to the...
View ArticleClik here to view.
Problems with phone apps
@Kingjohn wrote: I have a PBXact machine that came with phone apps. When I set up the profiles in EPM the Aastra phones take the information but I continue to get an error when I try to use the button...
View ArticleEndpoint Manager won't create config file for remote Yealink T26P
@manageddc wrote: I've got a site with an odd problem, I am trying to use the commercial EPM to provision a Yealink T26P as a remote phone, via VPN.... Anyways, so the issue is this, I can add the...
View ArticleClik here to view.
Endpoint Manager will not change basefile for Yealink phones
@sorvani wrote: I have a newly installed system that I am trying to setup the endpoints for and I am having problems with EPM. The basefile edits are not doing anything. Pasted image987x341 29.4 KB I...
View ArticleQxact export
@assos40 wrote: Hi,I have following issue.When i am trying export a big report for example 'answered call details' (about 9000 records) the browser states'This website is not found'On exacltly 30...
View ArticleWe are unable to process your order as you are trying to renew a trial module
@GSnover wrote: Just updated from FreePBX 11 to 12 (I am in the process of bringing this box current) and I am getting the above message when I try to renew Endpoint Manager - Did I have a trial? How...
View ArticlePanasonic TGP500 Hanging during tftp provision
@dbayer wrote: Hello,I'm trying to provision a Panasonic TGP500 portable phone. I'm able to provision without issue my Sangoma Phones. While watching the TCPDump of the tftp communication, I can see...
View ArticlePark and Announce
@fcd_3 wrote: Is setup, running Freepbx13 (10.13.66-11). Calls to the Park and Announce extension show up in the log file as an outbound (external) call. [2016-09-01 08:27:34]...
View ArticleOur deployments became not activated after enabling a second Ethernet interface
@jronald wrote: Our deployments became not activated after enabling a second Ethernet interface. I was able to re-activate them by resetting the hardware lock using the portal. I now only have one...
View ArticlePolycom Basefile Edit Phantom Calls
@miconib wrote: I know there is a line that you can add to the polycom config file that will tell it to only allow traffic from certian IP address. I'm assuming that this will stop the phantom calling...
View ArticleBroadcasting: delay in playing a message on answer
@bksales wrote: Is there a way to change the behavior, or did that change in one of the recent updates? Ideally I'd like it to behave the way it did before. I tested on my cell phone and if I don't...
View ArticleClik here to view.
Couple Issues - EPM & PhoneApps
@zigge wrote: FreePBX: 10.13.66-15Asterisk: Asterisk 13.10.0 EPM Module: 13.0.18.1PhoneApps: 13.0.76RestAPI: 13.0.19Device: Aaasta 6755i (55i)Device Firmware: 3.3.1.4358 Similar Topics:...
View ArticleFax ProModule Setups
@garretn wrote: I purchased the Fax Pro Module and have installed it and it shows enabled but I do not see any of the setups screens to be able to set global settings and user settings. UCP doesn't...
View ArticleEPM error in basefile
@jarvisswope wrote: All Modules are up to date | FreePBX 13 LDAP Number Attributes. This setting specifies the �number� attributes of each record which are returned in the LDAP search result...
View ArticleEPM Sangoma Firmware Missing
@cashflw wrote: PBX Firmware: 10.13.66-13PBX Service Pack: 1.0.0.0EPM: 13.0.84.3 I have available firmware 1.19 in firmware slot 2. and 1.17 in slot 1. When I look in the /tftpboot/sangoma/2 folder on...
View ArticleSangoma Phones - Check for upgrade every
@cashflw wrote: EPM 13.0.84.3Phone Firmware 2.0.4.13 or 2.0.4.15Phone Model s500 or s700 In EPM under Global Settings, ReSync Time is set to 86400 (seconds). When I look at the basefile, I...
View ArticleError in EPM when attempting to save template
@bodger wrote: Hello, I'm using FreePBX 14 (Framework 14.0.1alpha22) and Endpoint Manager 13.0.84.3. There is an issue when attempting to save a template in EPM. The error returned is...
View Article
